The old horse doesn't spoil the furrow. An old horse, it doesn’t spoil the furrow D link dir 320 entrance

The Dir-320 router, the brainchild of the popular company D-link, is a wireless router with a data transfer speed of 54 Mbit/s and USB 2.0 support.

Unfortunately, at present this model is practically no longer relevant, since the technical characteristics of the router - according to current demands - leave much to be desired.

Therefore, relatively recently - in 2011, the D-link company released the updated Dir-320 NRU with support for WiMAX, 3G GSM, CDMA and a data transfer rate of up to 150 Mbit/s - for 2011 this is enough good performance.

Brief overview of the dir 320 router

Detailed list technical characteristics The router is shown in the following illustrations:

The router body is black with one external antenna on the right side of the router.

The indicator panel consists of 8 elements:

• “Power” - power on/off;
• “Internet” - if the indicator is blinking, traffic is being transmitted, if it is just “on”, the connection is established;
• “Wireless network” - blinking – data is being transferred, “lit” - the network is active;
• “Local network 1-4” - blinking – traffic is being transmitted over the corresponding port, “lit” - the network device is connected;
• “USB” - “lit” - an external USB device is connected, flashing - the connection is established.

Rear panel of router dir 320:

• “LAN 1-4” - ports for connecting network devices;
• “Internet” - port for connecting to an “Ethernet line” or DSL modem;
• “USB” - port for connecting USB modems;
• “5V-2A” - connector for connecting a power adapter;
• “Reset” is a button used to reset to factory settings.

How to set up an Internet connection on a d link dir 320 router?

Prepare an agreement with your service provider in advance, as it will contain the authorization data necessary to set up an Internet connection.

To enter the router settings, you need to connect the router d link dir 320 To and enter the address 192.168.0.1 in the browser address bar. When prompted for a login and password, enter “admin/admin”.

If your router has been in use before, then before making settings you need to reset its configuration to the factory one using the Reset button. Otherwise, authorization errors may occur (for example, an incorrect login and password will be specified) and problems with setting up the device.

Below is appearance router interface d link dir 320 from software version “1-2-94”, which is stock by default.

After logging into the web interface for the first time, you need to change the administrator password (in order to secure the network from possible unauthorized entry), and then click the “Save” button.

To create a new Internet connection, open the “Network” section, then “Connection”, click the “Add” button and do the following:

• “Name” - leave unchanged;
• “Connection type” - this parameter depends on the authorization data from the agreement with the provider.

Choose one of the options:

PPPoE

• in the “PPP Settings” block, enter “Username” and “Password” (twice);
• tick the following options: “Keep Alive” - connection support, “NAT” and “Firewall”;
• If desired, you can enable “PPP Debugging” - entering debugging entries over the connection and “PPPoE Forwarding”.

IPoE

• check the boxes “Obtain an IP address automatically” and “Obtain DNS server address automatically”;
• “Vendor ID” - if required by the provider.

PPTP or L2TP

• if you need the connection to be carried out automatically, select “Connect automatically”;
• “Service name” - enter ip or url address authentication server;
• indicate “Username” and “Password”;
• in the “Encryption” line, select one of the options: “Off”, “MPPE 40/128 bit”, “MPPE 40 bit” or “MPPE 128 bit”.

3G

• in the “Mode” line, select “Auto”;
• authorization data is filled in by analogy with the above;
• “APN” - access point name;
• “Dial-up number” is the number for connecting to the operator’s authorization server.

Setting up wifi on a router d link dir 320

To configure wireless network select " General settings" and click "Enable wireless connection".

• indicate in the “SSID” line the name of the network being created;
• “Country” and “Wireless mode” - no changes;
• in the “Channel” line - select either “Auto” or from 1 to 13;
• if you plan to limit the number of connections to the network, indicate the desired number in the “Maximum number of clients” line.

Then open “Security Settings”.

Select one of the following options in the “Network Authentication” line:

A). "Open", "Shared" or "WEPAUTO"

b). "Open-IEEE8021X"

c) “WPA-PSK”, “WPA2-PSK” or “WPA-PSK/WPA2-PSK mixed”

Depending on your selection, enter the security key that will be required for subsequent connection wifi devices to a wireless network.

Setting up IPTV

Please note that the “IPTV” section is present only in software versions “1_3_3” and “1_4_0”.

Settings are made in the “IPTV Setup Wizard” menu

Here you only need to select the port number to which the set-top box is connected.

• click "Add";
• “Type” - for “IPTV” select “Transparent”;
• Specify “VLAN ID” if required by the provider;
• in the “Port” line, select the port number to which the set-top box is connected.

To complete the settings for the d link dir 320 router, click “Save changes”.

In version “1-2-94” there is no “IPTV Setup Wizard” section. In the Advanced menu, check if "IGMP" is enabled:

Additional features of the d link dir 320 router

As additional settings It’s worth paying attention to “WMM” (Wi-Fi Multimedia). In short, it is a protocol for prioritizing voice traffic (AC_VO), video traffic (AC_V), traffic from devices without a QoS mechanism (AC_BE), and traffic without latency and performance requirements (AC_BK) over normal traffic passing through wireless network.

• “Aifsn” (variable interframe interval coefficient): the lower the value, the higher the priority;
• "CWMin/CWMax" (minimum and maximum size concurrent access windows);
• "Txop" (data transfer capability);
• "ACM" (Access Control Mandatory);
• "Ack" (reception confirmation).

There is no big difference in the external component of the “web interface” between versions “1_2_94” and “1_3_3”.

However, starting with version “1_4_0”, the router interface is more similar to: the main elements can be found in the following illustrations:

In order to connect your computer to the Internet, the user needs to configure his router and himself. Only after this will it be possible to easily open various electronic pages of websites and download the necessary information.

Connecting a router

Setting up and connecting the D-LINK DIR-320 router begins with checking the functioning of important network nodes on the router itself and the computer.

To get started, you need to do the following:

Photo: Network designation on the taskbar

If everything is done correctly, then you can start setting up the router itself and the connection.

Login to settings via web management

Before you start setting up D LINK DIR 320, you need to check the operation of network devices.

To do this, you need to perform the following procedure:

These steps are necessary to prepare automatic settings wifi router d-ink dir 320 and local network.

After setting up a local connection, you need to launch the disk included with the router. It is necessary to create local connection to the Internet and settings of the router itself. This is done according to the prompts that pop up in the installation window.

Particular attention should be paid when choosing the connection technology parameter - pppoe or l2tp. You should choose a connection format in accordance with the parameters specified in the Internet connection agreement.

The next step is configuration via the web interface. To do this, you need to type the IP address 192.168.0.1 in your Internet browser.

The login and password are in the instructions, which the system will prompt you to change after logging in.

After changing the login and password, an interface will appear on the screen in which all connection parameters will be indicated, including all possible settings parameters based on the provider’s technology.

Photo: Interface with connection parameters

The standard router kit includes a disk with software necessary for the correct operation of the network device, but this does not guarantee the uninterrupted and correct functioning of the D-LINK DIR-320.

How do I configure and install the latest version of the required drivers?

Update software for the D-LINK DIR-320 router only passes through home internet pages – 192.168.0.1. This procedure should be carried out immediately after installing the basic software from the disk by following the link “ftp://dlink.ru/pub/Router/DIR-320_NRU/Firmware/”. Download and save the file to your desktop.

Photo: Firmware updates for DIR-320

Thus, the path to the file is set, on the basis of which the router software will be updated. When carrying out this operation, you cannot turn off and restart the computer before it is completed, otherwise a failure may occur and you will have to start installation and configuration from the very beginning.

Photo: Software update progress

When the update is complete, the DIR-320 will reboot.

Setting up the D-LINK DIR-320 router from providers

The providers themselves often take advantage of the information weakness of users, most of whom are simply afraid to get into the hardware and figure it out on their own. In this regard, it is always possible to call an appropriate specialist to your home to carry out the appropriate work on setting up the Internet.

For example, you can order setup of the D-LINK DIR-320 router from Rostelecom by dialing the technical support number. The operator will listen to all your problems and offer a convenient time to call a company specialist at your home.

In fact, all these steps are simple, and you can do them yourself without additional expenses.

To do this, you must adhere to the following sequence:

This sequence of setting up an Internet connection is applicable to the operating room. windows system 7 and 8.

Setting up for Rostelecom

To configure the router D-Link DIR-320 in the Rostelecom provider network, the user must go to home page router (192.168.0.1) and perform the following steps:

Setting up for Beeline

Setting up the D-LINK DIR-320 router for the Beeline provider differs from Rostelecom, because they use the connection type "l2tp".

So the user's actions should look like this:

If everything is done correctly, the user will be able to freely use the Internet.

Setting up for MTS

Connection to the Internet from the MTS provider uses pppoe technology.

Therefore, setting up the D-Link dir 320 router will proceed as follows:

1. checking the operation of the network device;
2. go to the home page of the router in the Internet browser 192.168.0.1;
3. install drivers;
4. update drivers;
5. go to the “network” tab and select the “connections” line;
6. in the window that opens, select the “add” option;
7. connection type is set to “pppoe”;
8. check the “allow” box;
9. in the line “physical interface” set the parameter “port5”;
10. in the user name and password lines we enter the corresponding data from the agreement with the provider;
11. in the “NAT” and “firewall” lines, check the boxes;
12. save the parameters and configuration.

Video: Setting up a D-Link dir router

Setting up Megafon

Internet from Megafon is mainly provided using 3G technology. Therefore, all settings are set manually:

1. go to the router page 192.18.0.1;
2. select the “Internet installation” column;
3. in the updated window at the bottom, select the option “set up an Internet connection manually”;
4. in the window that opens, select the connection type “3 GUSB adapter”;
5. in the fields of login, password and dial number in accordance with the parameters issued by the provider under the contract;
6. save the parameters.

Wireless connection

Network operation via the wi-fi module of the DIR-320 router is very simple and convenient. To set up a wireless connection, just follow the prompts during the initial installation of the driver on the router. If a corresponding message appears during the installation process, you should set the recommended parameters according to the prompts.

Photo: Wi-Fi item in the main window of the web interface

The main attention should be paid to the settings network card on a computer to support wi-fi connection. In this case, you need to go to the control panel, and in it select the network control center and shared access. Next, enter the option to change adapter properties and check the status wi-fi works module. If everything works, then the connection to the Internet will occur immediately and without delay.

Wi-Fi connection settings in Windows 7

If the connection to the Internet does not occur automatically, and this only happens when using older versions of D-LINK DIR-320(b1) or the windowsxp operating system, then you will need manual setting. To do this, you need to go into the settings of the wireless connection adapter and manually set the IP and DNS address. In this case, the IP address will correspond to the router address, and the submask (dns) will be 255.255.255.0.

Next, the user must create a new connection without changing the parameters. You only enter your login and password information to connect to the Internet, and a shortcut is created on the desktop, when opened, a direct connection occurs.

So to carry out full customization your D-LINK DIR-320 router, you need to:

• carefully read the instructions for the router;
• check the operation of the network card and local network settings on the computer;
• install drivers and configure the connection according to the prompts during the installation process;
• update drivers to the latest version.

Experienced users can easily cope with such a task, but for beginners it will be difficult. But if they configure their router strictly in accordance with the indicated order, then the result will not be long in coming.

Connecting the D-Link DIR-320 router to a 3G modem. The DIR-320 router manufactured by D-Link is not the most popular router model. However, this device is best suited for connecting a 3G modem. If you want to set up a wireless Internet connection not only for a computer or laptop, but also for mobile devices, create local network using a 3G modem and router. Why should you choose D-Link DIR-320? Firstly, this router has all the characteristics necessary to create such a network. And secondly, it can be purchased at an affordable price.

The characteristics of this router largely coincide with the D-Link DIR-300 model, but there are several significant differences. D-Link Router DIR-320 is equipped USB port 2.0 type A, designed for connecting a USB modem. The port is located on the back cover of the device, it is the first connector on the left.

The router supports automatic connection to a 2G/3G wireless network. Among additional functions– the ability to enable/disable PIN code verification and PIN code change. There are several firmware versions for the D-Link DIR-320 router. The optimal firmware version for setting up a 3G modem is DIR_320NRU-1.2.94, it can be downloaded on the Internet. If your device has a different firmware version installed, this is not critical. You can also connect a 3G modem, the setup process will just take longer.

Connecting the D-Link DIR-320 router to a 3G modem - go to the router

So, let's consider connecting a router with firmware DIR_320NRU-1.2.94. Let's set it up first operating system computer: prepare a network card and determine the provider settings. Then you can start connecting and configuring the router. To do this, connect the device and open any Internet browser. In the address bar, enter the IP address of your router (default is 192.168.0.1).

Press Enter, after which the authorization window appears. Now you need to enter your username and password. By default, the Username/Password combination looks like “admin/admin”. Fill in these fields and click the “Login” button. The system will prompt you to change your password for security purposes. Install New Password and save the settings. Then the authorization form will appear again, where you need to enter “admin” in the “Username” field and a new password in the “Password” field.

Connecting the D-Link DIR-320 router to a 3G modem - setting up connections

In the window that opens, select “Network”, and then “Connections”. A table will immediately appear, below which there is an “Add” button.

By clicking on this button you will be taken to the connection settings menu. Then set the connection type to “3G”.

In the “PPP Settings” section, fill in the fields “PPP Username”, “Password”, “Password Confirmation”, “APN” and “Dial-up Number”. We leave other fields unchanged. Click the “Save” button.

Information about the created connection will appear in a new window. Next to the desired connection, select “Default Gateway”. Then click on “Save” in the upper right corner. After that, in the “System” window that appears, click “Save with reboot.”

If the SIM card used in the 3G modem has a PIN code, enter the USB modem menu. Select the “PIN” section, enter the code in the appropriate field, then click “Change” and save the settings. This completes the connection of the router to the 3G modem.

The D-Link DIR-320 router can be used not only to work with the 3G standard. You can set up any other type of Internet connection. This will be easy thanks to the convenient and intuitive interface of this

This manual shows and describes in detail how to set up a D-Link DIR-320 Wi-Fi router for Beeline and Rostelecom Internet.

Let's look at the following points step by step:

• How to connect DIR-320 to the Internet line and computer for setup
• How to set up an L2TP connection for Beeline Internet and PPPoE for Rostelecom
• How to set up a Wi-Fi password and wireless network name
• Setting up IPTV television (Digital TV Beeline and Rostelecom).

So, everything you might need to set up this wireless router is here, you just have to read it carefully.

How to connect a router

I’ll start with how to properly connect a Wi-Fi router to configure it, since even here there are problems.

On the back of the D-Link DIR-320, not counting the power supply and a couple of buttons, there are five ports: 4 LAN and 1 Internet. It is to the last connector that you need to connect the cable from your Internet provider.

I also note that the setup itself will be easier if you perform it from the computer that is connected to the router by wires: connect one of the LAN ports on the device to the network card connector on the computer.

And the last two points:

• When setting up, the Beeline, Rostelecom or “High-Speed ​​Connection” connection on the computer must be disconnected. And after you configure it, do not launch it either - the router itself will connect to the Internet.
• If you are unable to enter the router settings, as described below, .

So, now you can begin the setup itself.

Logging into the settings web interface

To enter the D-Link DIR-320 settings, launch the browser and enter 192.168.0.1 in the address bar, you should see a login and password request. Standard login and password, if you have not changed them before - admin(if the password does not match, then you will be thrown back to the password entry page. It may have been changed. Then you can reset the router to factory settings by pressing and holding the Reset button for 15-20 seconds).

After entering correctly you will be at home page with basic information about the device. Click "Advanced Settings" at the bottom of the page.

Setting up D-Link DIR-320 for Beeline

To configure the connection, in the “Network” item, select “WAN”, a list of connections will open. At the bottom of the list, click “Add” and set the following Beeline Internet connection parameters:

• Connection type - L2TP + Dynamic IP
• Login, password - your Internet login information that you received from Beeline
• VPN server address - tp.internet.beeline.ru

There is no need to change any other settings. Click “Save”, after which the page with the list of connections will open again, and at the top there will be a notification with a unit, click on it and click “Save”.

Now, if you refresh the page, you should see that the connection you just created is now in the "Connected" state, which means that the Internet is configured correctly and you can go to Wi-Fi settings networks. Do not forget, the Beeline connection on the computer must be disconnected.

On the advanced settings page, under “Network,” click “WAN.” A list of connections will open, where there will be only one - click on it, and on the next page click “Delete”. You will be returned to the already empty list of connections. Click “Add” and enter the following parameters for the Internet from Rostelecom:

• Connection type - PPPoE
• Username and password - Internet login data provided to you by Rostelecom

The remaining parameters can be left unchanged; click “Save”. You will be returned to the list of connections. Please note that at the top of the DIR-320 settings page the “light” is lit, click on it and select “Save”.

Please refresh the page in a minute. If you see that the connection status has changed to “Connected”, then you have done everything correctly and the Internet is already available, you can proceed to setting up Wi-Fi. Let me remind you that the Rostelecom connection on the computer itself must be disabled.

Setting up a Wi-Fi network

In order to configure the wireless Wi-Fi network settings on the DIR-320, on the page with advanced settings in the Wi-Fi item, click “Basic settings”; on the page that appears, you can set your wireless network name (SSID) instead of the standard DIR-320.

Then save these settings and return to the “Wi-Fi” item, now you should select “Security Settings”. This is where the Wi-Fi password is set. Recommended settings:

• Network Authentication - WPA2-PSK
• PSK encryption key (password) - at least 8 characters, without Russian letters.

Save the settings, do not forget to also click “Save” at the top of the change indicator (light bulb). In general, the DIR-320 setup is complete.

TV setup

In order to set up digital television Beeline or Rostelecom, on the main page of the router settings, select “IPTV Setup Wizard”, in it indicate the port where the set-top box will be connected and save the settings. Connect the TV set-top box to the selected LAN port.

The DIR-320 model from D-Link is a fairly popular device for creating a home wireless network. This router is often recommended by store consultants as one of the most reliable and at the same time inexpensive. In addition, the DIR-320 is used by many providers as a standard router installed by clients when connecting to Internet services.

Typically, the router parameters are adjusted by a specialist invited to install the provider’s cable into the premises. However, there are situations when you have to do it yourself. To ensure that creating a connection does not become an insoluble problem, you need to know how to configure a d link dir 320 router.

Installing the router and preparing the system

The router is connected in a standard way. On the back of the router case you can find a number of connectors, among which we are interested in the WAN and LAN ports.

The WAN connector must be equipped with a cable supplied to the premises by the provider; The router is connected to the computer via the LAN connector using the included patch cord.

Preparing the system involves checking the network card parameters and local network connection properties:

WAN setup

To create a connection to the Internet, you need to get into the router interface. It is available at 192.168.0.1. (authorization pair – admin/admin).

The interface looks standard for D-Link routers with installed latest version firmware:
If you set up the D-Link DIR-615 router or other models of budget home routers from D-Link, you should have already understood all the available sections of the interface. If this is your first experience creating an Internet connection, then you will quickly learn to navigate here.

PPPoE connection

In the “Network” section, open the “WAN” item to open a list of available Internet connections.

If you already have a connection, do not delete it immediately. First and create a new connection. After setting up a new connection and saving the configuration, you can delete the old connection.

Leave the remaining parameters unchanged. Click the "Save" button to return to the list of connections. A light should light up in the notification menu at the top - click on it to update the hardware configuration.

L2TP connection

If you configured the upvel ur 315bn router to connect to Beeline, you probably encountered the need to specify the VPN server address. By the way, this is the only difference between setting up L2TP and PPPoE. Otherwise the procedures are completely identical.

Creating a Wireless Network

Users who have encountered the need to configure Wi-fi router ASUS RT-G32 or any other router knows very well what parameters need to be specified to create a wireless network at home.

At D-Link setup DIR 320 does not change anything in this sense:

Now you can close the router interface and try to search for the created access point from any device that has a Wi-Fi module.