Instructions for restoring flash drives. The best free programs for repairing flash drives Can’t see the transcend 16gb flash drive
Until recently, we stored music, videos and electronic documents on CDs or floppy disks. However, these media gradually disappeared, replaced by a much more compact and capacious flash drive, USB or simply a flash drive. It serves as a fairly reliable “storage” for any information, but even a USB drive
sometimes it breaks. What to do if the flash drive does not boot or is not recognized in the system? You can throw away an unusable drive and buy a new one if there is nothing important left on it. But sometimes a thesis or the only copy of an important document remains there, and it has to be restored. Transcend is no different from the same “operation” with any other brand of drive.
So, let's consider a situation in which the flash drive freezes during the recording process and is not detected when it is reconnected. At the same time in the list USB devices appeared, but the disk manager did not show its icon. These symptoms indicate a controller failure. Any drives, including Transcend flash drives, are based on a control chip or controller. Various failures or power problems block the controller, and inaccessible sectors appear on the USB. If the flash drive
stuck due to a system failure, you should do the following:
- Determine the name and manufacturer of the controller.
- Find a utility developed by this company.
- Transfer the control chip to test mode and restore.
Let's start restoring the Transcend flash drive by disassembling it into parts - this is the easiest way to find out the manufacturer of the chip. The USB drive is easy to disassemble; just bend the edge of the sticker on its body, press the latch with a thin object, which is hidden under the sticker, and carefully pull the connector. The controller is essentially a printed circuit board. On one side there is a chip, and on the other there is a memory chip. Both sides contain the data necessary for recovery.
Having decided on the controller manufacturer, we will continue restoring the Transcend flash drive. The next step is to search for a utility from the manufacturer. It must support the controller with this number. You can download the service utility from a resource that distributes free software. If no application on the flash drive is "view
it”, it should be switched to testing mode. Which contacts need to be closed for this are indicated in the drive documentation. Having found a suitable program, you should install the factory driver that came with it. You can find it in the folder with the installed utility.
Now the actual recovery of the Transcend flash drive begins. First, let's download the utility and start searching for the drive. After waiting for it to be displayed in the program, press the “Start” button, thereby starting diagnostics and formatting of the drive. Please remember that all data recorded on the flash drive will be erased. To restore the maximum capacity of a flash drive, it is worth formatting it twice. After the message about the successful completion of the “operation”, disable the factory driver, return the flash drive to normal operating mode and reboot it.
I hope that my story about how to recover data on a flash drive will come in handy more than once in a hopeless situation.
It is quite difficult to imagine a modern person without a digital storage device. A flash drive is currently a successful portable object on which a lot of useful information is stored.
The advantage of a flash drive is that it does not take up much space and is accompanied by increased practicality. Even when dropped, it is not always damaged, as was previously the case with disks.
Another advantage is that recording the desired content on it is not only faster, but also much easier.
Unfortunately, despite its unique practicality, it may happen that the flash drive stops functioning at some certain point.
Of course, you can peacefully “say goodbye” to the dead flash drive and go to the store where you can purchase a new digital drive.
If it’s difficult for you to get rid of your usual storage media so easily, then we recommend that you study the recommendations on how to restore a “dead” Transcend flash drive.
Recovery process
Before making minor repairs to a damaged Transcend flash drive, it is important to determine the reason why it failed.
Such a diagnosis can be compared with the treatment of a patient. The doctor also initially examines the patient, establishes a diagnosis, identifies the cause of the pathology, and only after that prescribes treatment.
We also recommend that you “treat” your affected digital media. The Transcend flash drive recovery program will help with this quite effectively, which can be easily downloaded using offers on the network.
However, it is still initially useful to establish the cause of the failure, due to which you have to “draw” advisory information.
Reasons for failure
In most cases, you have to consider restoring a Transcend flash drive due to a banal software failure that users have to deal with quite often.
Confirm that, indeed, software glitch presented this unpleasant surprise, allow some tricks.
Insert your drive into the USB connector and watch what happens next. If all your attempts to open the media are in vain, but the computer still sees the Transend flash drive, then it is likely that it has suffered a software failure.
You can suspect the same if, when you connect the media via a USB connector, you hear a characteristic sound signal, but no visible changes appear on the screen, including you will not detect your media when you launch the “Computer” window.
Also, a software failure is indicated by the factor when the PC sees the flash drive, but not all of it, but only part of its disk space.
Of course, if you find confirming “symptoms” of a software failure that requires recovery of the Transend flash drive, you don’t need to fall into despair and feverishly remember what could have caused such trouble.
Of course, you could have caused the digital storage device to fail if you neglected the recommendations on how to properly remove the drive from the USB connector.
The reason for the failure may be a fall of the device or strong mechanical compression. There may also be reasons that are completely independent of the user’s actions.
Troubleshooting
Those who are convinced that the drive has stopped responding to any actions want to find a program for flash drive recovery.
Indeed, a utility for restoring a Transcend flash drive exists; it is not so difficult to find, download and install on a computer.
One of the programs for flash drive recovery
However, it is initially important to make sure that the digital drive is still “dead”. Sometimes it happens that it does not respond on one PC, but functions perfectly on another computer.
Often a software failure is detected on the PC itself, when, for example, the drivers have crashed.
You can also try disconnecting everything from the USB connectors. peripherals, and connect only the USB flash drive. Even such a simple move can sometimes easily fix the problem.
If all attempts are in vain, we recommend that you inspect your digital drive from all sides. It is useful to pay attention to all chips and cracks that you find on the body.
It wouldn’t hurt to look inside the part that connects to the USB connector. Sometimes such a visual inspection is enough to identify poor internal contact.
Don’t be afraid to carefully open the media case and inspect it for integrity inside. It is useful to carry out a thorough visual inspection of its internal contents.
You can also try to fix bad contact yourself, but only if you have special tools for this. If there are none, you are unlikely to be able to eliminate even the identified problems.
Only after you are sure that mechanical damage is excluded, you can move on to the next stage, after completing which the digital media can be restored.
Of course, in this case you will definitely need a Transend flash drive recovery program.
To correctly restore a flash drive, it is important to first clarify the type of memory installed on the media, its ID, firmware version, controller ID and other technical details.
In this case, you will not be able to do without the help of the special Chip Genius utility. With such a utility, you will not only receive information quickly, but it will be accurately presented without errors.
Based on the information received, you can begin a search, the purpose of which is a program to recover your flash drive.
The ideal solution to the problem you identified is not even a recovery utility, but the JetFlash Online Recovery service program.
This option is suitable for those users whose computer is provided with constant and reliable access to the Internet.
Don’t even get yourself ready for a labor-intensive process; your expectations will be in vain. Immediately after launching such a service program, as well as connecting the digital “dead” drive to the USB connector, the “reanimation” process will start automatically.
You just have to wait patiently for the process to complete. The only thing you have to do is click on the “Yes” button, confirming your willingness to grant the rights to work with the flash drive to the program itself.
Once the work is completed, the program will notify you about this. Now unplug the flash drive and then plug it in again. If the resuscitation process was effective, you will instantly find that your digital drive has come to life. You can again perform copying, recording and other functional user manipulations on it.
If the flash drive still doesn’t come to life, you’ll have to say goodbye to it and buy yourself a new digital “assistant.”
So, you were able to see that the process of recovering digital media is not complicated. However, such a process requires increased attention and responsibility for every step taken.
Hi all! It’s not for nothing that I decided to write an article on how to flash a flash drive – I have experience. Yesterday I restored my flash drive Kingston DT Elite 3.0 16GB. Everything worked out, and I thought, why not write similar instructions, and tell me what to do and how to do it, in order to give the flash drive a new life :).
Nowadays, probably every house has a flash drive and very rarely just one. It’s convenient to transfer information onto them, they’re beautiful, and besides, they’re not expensive these days. But very often USB drives fail. If we talk about why this happens, then we ourselves are in first place. Do you always do a safe removal of your flash drive? So I rarely do. There may, of course, be other reasons why flash drives simply “die”.
One point needs to be clarified here. It happens that the flash drive really “dies”. In this case, it is impossible to restore it. At least at home. But if USB drive, when connected to a computer, shows at least some signs of life, then you can try to restore its operation using the controller firmware.
What signs of life might there be for a USB drive?
- When you connect the flash drive to the computer, the computer signals that the device is connected - that’s good.
- At Windows connection ask to format the removable drive (but during the formatting process there are problems and errors such as “Windows cannot complete formatting”).
- The flash drive is detected and visible in Explorer, but when you try to open it, the message “Insert disk...” appears.
- Errors occur when copying information.
- Very slow speed recording/reading information.
If there is valuable information on the flash drive, then you can try to restore it before and after the firmware. This can be done using different programs. I advise Recuva, here is the article but there are many other good programs.
If the information is very valuable, then it is better not to do anything yourself so as not to make it worse. Contact special service centers who are engaged in information recovery.
Let's now look at the entire process of flashing the controller on real example, using my Kingston DataTraveler Elite 3.0 16GB flash drive as an example. My flash drive broke down. It’s interesting. I needed to upload files to it and delete those that had already been recorded. I connected it to the computer and started deleting the folder. But the folder was deleted very slowly. I disconnected and reconnected this flash drive, and a message appeared that the disk must be formatted “Before using the disk...”.
Since it was not on the flash drive Important files, I didn’t hesitate to start formatting.
But the process itself lasted a very long time and never ended, I forcibly stopped it. The message “Windows could not complete formatting” may also appear.
But still, I formatted it, the tenth time, and only in FAT 32. After which the USB drive was detected normally and I was even happy. But that was not the case. I started copying files onto it, and the recording speed was approximately 100 kb/s. I decided to flash it, which I did.
Determining the VID and PID of the USB controller
First we need determine VID and PID. This is data about the model and manufacturer of the controller, which is located in our drive. Using this data, we will look for a utility for the firmware. There are many different programs, with which you can determine the VID and PID. I recommend the utility Flash Drive Information Extractor You can download it from the link.
Connect the USB flash drive to your computer and run the Flash Drive Information Extractor program (extract the program folder from the archive and run the GetFlashInfo.exe file).
Click the button at the top of the program “Get data about the flash drive”.
The program will give us the result. We look at the information that is located opposite VID and PID.
You can copy these numbers, or leave the utility window open, we will now need the received data.
We are looking for a utility for flashing a flash drive
Based on the VID and PID data, we need to find the utility with which we will flash the controller. There is a good website flashboot.ru, which contains a database of flash drives and utilities for their recovery.
In the search results we look for a flash drive similar to ours. The list may include devices from other manufacturers. They just have the same controller, it was identified by VID and PID. You may have noticed that I have a 16 GB flash drive, but in the list I highlighted 32 GB. I think there's nothing wrong with that (just where the name of the utility is not indicated on 16 GB). You try to choose a more similar device from the list.
We are interested in the field UTILS(utility), copy its name in full.
Unfortunately, the utility that I need was not found on this site. Perhaps you will have better luck and you will see something in the search results. Download the utility to your computer.
But I didn’t stop there and started Googling. I just asked “SK6221 MPTool 2013-04-25” and found this utility on some other site. If you have the same flash drive, then this utility is . True, the name of the archive is different, but this did not stop me from successfully curing my flash drive.
USB drive recovery process
Disconnect the flash drive. Extract the folder with the utility from the archive and run .exe file. In my case it is the MPTool.exe file. Also look text file readme.txt. Perhaps there are instructions there, or a link to a site with instructions. If the instructions are in English, then translate it using the same translate.google.ru.
I'll tell you how I did it (you just may have a different utility and everything may be different there, but it should not be very different).
The utility is running. We connect the flash drive. I have information about the flash drive in two lines in the program. Press the button Start. In my case, the yellow strip signaled the firmware process. We are waiting.
When the process was over, I saw a green color, everything seemed to be fine.
Should appear immediately Windows message prompting you to format the disk. But most likely nothing will work out the first time. Unplug the flash drive and plug it back in. The driver should be installed and the removable drive should appear in Explorer. You can format it.
I checked the recording speed, everything is as it should be for USB 3.0, everything is fine!
You need to be prepared for the fact that the actions may differ from those I described. And not everything can work out the first time. The main thing is not to give up and everything will work out!
Sooner or later, most users encounter a situation where the flash drive is displayed incorrectly (here you can try formatting first) or the information on it suddenly disappears. But do not despair - it is likely that you yourself will be able to revive the device and successfully restore the photos and documents stored on it or “bring to life” the file system.
Thanks to our recommendations, you can save not only on the services of a specialist, but also on special programs- we will consider exclusively free software for repairing flash drives. However, it is also worth keeping in mind that different utilities are designed for devices from different manufacturers.
If you don't know the model of your USB drive
do the following:
Go to the Start menu and in the “Run” line write mmc devmgmt.msc, then press Enter. In the Universal Serial Bus Controllers section, find your “USB Mass Storage Device”, select it and right-click. Open Properties, then go to the Details tab and in the dropdown select Device Instance Code (or Hardware Codes). Write down or remember the PID and VID.
Then go to the FlashBoot.ru website and enter the VID and PID data in the special field. After this, you will receive information about your device and the utilities that are best suited to repair it.
Recovering a Transcend flash drive
To restore devices of this brand, the official Transcend RecoveRx utility is best suited. With its help, you can conduct an in-depth search deleted files, which you can later also restore: photos, documents, audio and video files.
By the way, RecoveRx supports all types of storage devices, including memory cards, MP3 players and external hard drives. This program works extremely simply - you just need to specify the type of files or select all.
The second method is online recovery of flash drives from the JetFlash Transcend series. To use it, you must download JetFlash Online Recovery (you must have an active Internet connection). Once launched, the tool will automatically restore all your data.
Silicon Power flash drive recovery
If you have a Silicon Power flash drive, you are in luck - the manufacturer cooperates with Recuva. The File Recovery tool provides a clear interface that will allow you to quickly scan your device and mark those that are subject to reincarnation. More details about the features of the work the specified program you will be able to read.
Kingston flash drive recovery
If you have lost files on media from this company, a flash drive recovery utility can also help you. If you have problems with the operation of the device, then most likely you will have to format it, and this cannot be done Windows tool, and the official Kingston Format Utility. Just launch it, select your device and click “Format”.
Recovering a SanDisk flash drive
USB drives from SanDisk have a five-year warranty, so if you suddenly encounter problems, feel free to go to the store or contact the manufacturer (e-mail.
Transcend removable storage devices are used by a very large number of users around the world. It’s not surprising, because these flash drives are very inexpensive and last quite a long time. But sometimes some kind of misfortune happens to them - information is lost due to damage to the drive.
This can happen by various reasons. Some flash drives fail because someone dropped them, others simply because they are old. In any case, every user who has a Transcend removable drive should know how to recover data on it if it has been lost.
There are proprietary utilities that allow you to very quickly recover data from Transcend USB drives. But there are also programs that are designed for all flash drives, but they work especially well with Transcend products. In addition, it often helps when working with flash drives from this company standard way Windows data recovery.
Method 1: RecoverRx
This utility allows you to recover data from flash drives and protect them with a password. It also allows you to format drives from Transcend. Suitable for absolutely all removable media from Transcend and is proprietary software for this product. To use RecoveRx for data recovery, follow these steps:
Method 2: JetFlash Online Recovery
This is another proprietary utility from Transcend. Its use looks extremely simple.
Method 3: JetDrive Toolbox
Interestingly, the developers position this tool as software for Apple computers, but it works very well on Windows too. To perform a restore using JetDrive Toolbox, follow these steps:
JetDrive Toolbox actually works exactly the same as RecoveRx. The difference is that there are many more tools.
Method 4: Transcend Autoformat
If none of the above-mentioned standard recovery utilities help, you can use Transcend Autoformat. True, in this case the flash drive will be immediately formatted, that is, there will be no chance of extracting any data from it. But it will be restored and ready for work.
Using Transcend Autoformat is extremely easy.
- and run it.
- At the top, select the letter of your storage medium. Below, indicate its type - SD, MMC or CF (just check the box next to the desired type).
- Click on the button Format" to begin the formatting process.
Method 5: D-Soft Flash Doctor
This program is famous for running at a low level. Judging by user reviews, it is very effective for Transcend flash drives. Repairing removable media using D-Soft Flash Doctor is done as follows:
If repair using all the above methods does not help restore the media, you can use standard means Windows recovery.
Method 6: Windows Recovery Tool
Judging by the reviews, these 6 methods are the most optimal in the case of a damaged Transcend flash drive. Less efficient in this case is the EzRecover program. How to use it, read the review on our website. You can also use D-Soft Flash Doctor and JetFlash Recovery Tool. If none of these methods help, your best bet is to simply buy a new removable storage device and use it.
